Contents
  1. YLOD Repair Guide
  2. ciofreedopadkin.tk – Just another WordPress site
  3. YLOD Repair Guide
  4. Gilksy's Playstation 3 (PS3) Yellow Light of Death (YLOD) Fix and Repair Guide

This the Gilksy's infamous PDF file that will teach you on how to repair a PS3 that has the Yellow Light of Death using a heat gun (re flowing it). PS3 YLoD Motherboard Repair Guide, With Gilksy Videos. This the Gilksy's infamous PDF file that will teach you on how to repair a PS3 that has the Yellow. Thank you very much for reading ps3 ylod repair guide gilksy. Maybe you have knowledge GILKSY PS3 YLOD FIX PDF - ciofreedopadkin.tk YLOD MOTHER.

Author:MITCH ALLANSON
Language:English, Spanish, Dutch
Country:Sierra Leone
Genre:Personal Growth
Pages:757
Published (Last):11.01.2016
ISBN:705-6-64710-446-4
Distribution:Free* [*Registration Required]
Uploaded by: JESS

46716 downloads 144468 Views 24.51MB PDF Size Report


Gilksy Ylod Pdf

PS3 YLoD Motherboard Repair Guide, With Gilksy Videos. PS3 YLOD Repair Guide by gilksy - PDF format If you found this guide useful and. PS3 YLoD Motherboard Repair Guide, With Gilksy Videos. As our and a detailed explanation about Ebook Pdf Ps3 Ylod Repair Guide Gilksy, its. Ps3 Ylod. Visit the website currently and get the report or review Ps3 Ylod. Repair Guide Gilksy by ciofreedopadkin.tk Studio online. You can get it as pdf, kindle, word, txt.

T Torx Security screwdriver or a small flathead screwdriver. Paper towels or a clean rag to clean up old thermal paste. Isopropyl Alcohol for thermal paste cleanup. Other cleaners may be substituted. Vacuum or canned air to clean case and system of dust. When you are ready to start the repair, you should download the PDF and print it to use as a guide while you do the repair 1. Using a small flat blade screw driver or slotted torx bit, unscrew cover plate screw. Slide cover plate towards the left until it stops and lift off. Remove all Phillips screws marked noting size and position. Hinge case towards you until disengaged and then tilt towards the left. See below. Remove ribbon cable by carefully lifting black part of connector locking tab. Remove 5 screws and the earth wire screw on psu, and unplug connector plug. Before removal of psu unplug small bnc connector black wire and remove tape on side of psu, now lift off psu. Now remove the wide ribbon from connector lift tab unscrew the four screws on the Bluetooth board and remove.

Lift of metal cover plate whilst allowing ribbons to pass through gaps in plate without damage, see below. Taking note where heat sink rubbers are positioned. Supporting fan assembly turn board over, remove fan power connector and fan.

YLOD Repair Guide

Remove 2 screws holding plate to hard drive connector and unplug battery connector. Now remove plate. Clean off old heat sink compound from the 2 mainprocessors using Isopropyl alcohol making sure all traces of the old heat sink compound has gone.

Typical example of dust build up. Ps3 case dusty. Heat sink plates before heat sink compound removed dusty. Once cleaned you should now have a nice pile of bits that looks something like this, see below.

Now for the tricky bit! Check the top metal cover plate underside for burn-in marks, as you can see below this ps3 got very hot before it yloded!

Place the ps3 mother board on a flat heat resistive surface kitchen work top or melamine shelf will be fine. Turn heat gun on and set temperature to deg and the fan speed to low to high and it will move the surface mount bits. Allow gun to get up to temperature before continuing! Paper towels or a clean rag to clean up old thermal paste.

Other books: INVENT TO LEARN PDF

Isopropyl Alcohol for thermal paste cleanup. Other cleaners may be substituted. Vacuum or canned air to clean case and system of dust. When you are ready to start the repair, you should download the PDF and print it to use as a guide while you do the repair 1. Using a small flat blade screw driver or slotted torx bit, unscrew cover plate screw. Slide cover plate towards the left until it stops and lift off.

ciofreedopadkin.tk – Just another WordPress site

Remove all Phillips screws marked noting size and position. Hinge case towards you until disengaged and then tilt towards the left. See below. Remove ribbon cable by carefully lifting black part of connector locking tab. Remove hard drive cover. Unscrew blue hard drive screw and disengage hard drive by sliding towards gap in the bay. Remove hard drive, see below. Unscrew 8 screws.

Lift enclosure out of plastic base, see below. Now unclip black rear panel and remove. Unscrew 4 screws and remove sprung brackets, see below. Supporting fan assembly turn board over, remove fan power connector and fan.

YLOD Repair Guide

Typical example of dust build up. Ps3 case dusty. Heat sink plates before heat sink compound removed dusty. CPU side first. After 15 to 20 seconds move onto the next area. Heat sink plates before heat sink compound removed dusty. Once cleaned you should now have a nice pile of bits that looks something like this, see below. Now for the tricky bit! Check the top metal cover plate underside for burn-in marks, as you can see below this ps3 got very hot before it yloded!

Place the ps3 mother board on a flat heat resistive surface kitchen work top or melamine shelf will be fine. Turn heat gun on and set temperature to deg and the fan speed to low to high and it will move the surface mount bits.

Allow gun to get up to temperature before continuing! CPU side first.

Gilksy's Playstation 3 (PS3) Yellow Light of Death (YLOD) Fix and Repair Guide

After 15 to 20 seconds move onto the next area. After 10 to 15 seconds move onto the next area. Heat sink compound still on in this picture, remove before reflowing. Heat sink rubber pads still on in this picture remove before reflowing also hold ribbons out of way while reflowing Congratulations!!

Now its time to apply new heat sink compound to the 2 processors, when doing this its always best to follow the manufacturers instructions but I believe the process is the same with all types please check instructions that come with paste , before continuing Use syringe supplied and dispense a small worm of compound from top to bottom on the left hand side of processor chip, now using credit card supplied spread compound evenly and thinly over processor face to much is bad and not enough is also bad the ideal amount is when you can almost see through the paste.

Now repeat on the other processor.